Specifications & Instructions

CR1 & CR2BB

TV Only

CR1R

For in room Cable Boxes

CR3BCB

TV Only
or
TV plus Cable Box

Specifications & Instructions

Clean Remote Spec Sheet


Instructions for CR1 and CR2BB Clean Remote®

  • Simple One Touch set-up (no codes needed)
  • For TV only (will not work TV/DVD, VCR or DVD/VCR combination units)
  • Works over 250 brands of commercial and retail TVs
  • No Menu button - So Patients and Guests cannot change settings
  • Hidden Battery compartment and attached door to help prevent batteries from being taken
  • Uses 2 AAA batteries
  • Will not operate with LodgenNet® or On Command® movie systems

Battery Installation:

1. Open cover: With keypad facing you, first slide dark lens cover away from you (photo A, step 1) and then lift lid upward from the back (photo A, step 2)

2. When placing AAA batteries in the compartment note the + and - symbols on the metal hinge should make contact with the corresponding + and - end of each battery (photo B).

3. Closing cover: With keypad facing away from you gently close cover by pressing downward
(photo C, step 1) and sliding it toward the front (keypad) until it is aligned. (photo C, step 2)

4. Test remote by pressing the power button; the LED should light indicating that the batteries are in correctly. If the LED doesn't light, then the batteries are either in wrong or the batteries are bad.

NO CODE ENTRY / ONE STEP PROGRAMMING

For all TV's

1. Turn on the TV and then stand back about 5 feet from TV and Point the remote at the CENTER of the front panel of the TV. It will not be necessary to point the remote at that exact area once the remote is set-up.

2. Press and firmly Hold down the Setup button, do not release. The LED will blink once and then after 7 seconds it will initiate code search. The LED will continue to blink every 2 seconds. Once your TV shuts off immediately remove your finger from the Setup button; the code automatically locks in.

3. Test the remote. If everything works, you are done. If the main functions are not working properly, you may not have an exact code match. Start again at step #1. The code search will continue where it left off.

Important Note: If you think you missed the code or are testing remote on different brand TV's: Reset the remote back to the beginning of the code search; first press and hold the
Setup button for 3 seconds and then while still pressing the Setup button down, press and hold the CC button down at the same time until the red LED light blinks quickly 3 times. You have now reset the code list back to the beginning. Go back to step 1.

View PDF Version (Printable)

INSTRUCTIONS FOR CR1R CLEAN REMOTE®

(Remote for TV with CABLE BOX)

  • Works over 250 brands of commercial and retail TVs
  • No Menu button - So Patients and Guests cannot change settings
  • Hidden Battery compartment and attached door to help prevent batteries from being taken
  • Uses 2 AAA batteries
  • Compatible with Comcast® and other cable system boxes
  • Will not operate TV/DVD, VCR or DVD/VCR combination units. Will not operate with LodgeNet® or OnCommand® movie systems

Battery Installation:

  1. Open cover: With keypad facing you, first slide dark lens cover away from you (photo A, step 1) and then lift lid upward from the back (photo A, step 2)
  2. When placing AAA batteries in the compartment note the + and - symbols on the metal hinge should make contact with the corresponding + and - end of each battery (photo B).
  3. Closing cover: With keypad facing away from you gently close cover by pressing downward (photo C, step 1) and sliding it toward the front (keypad) until it is aligned. (photo C, step 2)
  4. Test remote by pressing the power button; the LED should light indicating that the batteries are in correctly. If the LED doesn't light, then the batteries are either in wrong or the batteries are bad.
Battery Installation

FOR TV WITH AN INDIVIDUAL CABLE BOX IN EACH GUEST ROOM, START HERE: If you do not have an individual cable box in each guest room, scroll down to TV ONLY INSTRUCTIONS

  1. Manually turn on the TV and the Cable Box and then stand back about 5 feet from the TV. Point the remote at the CENTER of the front panel of the TV. It will not be necessary to point the remote at that exact area once the remote is set-up.
  2. Press and firmly Hold down the Setup button , do not release. The LED will blink once and then after 7 seconds it will initiate code search. The LED will continue to blink every 2 seconds. Once your TV shuts off, immediately remove your finger from the Setup button; the code automatically locks in.
  3. Turn TV back ON, DO NOT PRESS CHANNEL +/- buttons as you may change input on TV. Test the remote to make sure that you have the correct code by doing the following: Press Power ON/OFF and VOLUME + /- ONLY. If power and volume buttons work correctly on the remote then proceed to step #4. If you inadvertently changed the input on the TV, manually change it back from the TV's control panel and then try power and volume buttons ONLY. If the power and volume keys are not working properly, you may not have an exact code match. Start again at step #2, the code search will continue where it left off. Once you have the correct code, go to step #4 to program the cable box.
  4. To Program the Cable Box make sure the cable box and TV are on. Next, Hold Down the CBL button and CC button at the same time and wait until the LED light blinks quickly 3 times. Then immediately release both buttons. Now point the remote toward the cable box and TV and try the channel up and down buttons and the channel numbers. If the channels change correctly, make sure volume and TV power on and off work and assuming they do ,you are done.
  5. If the channels are not changing properly make sure the TV is on now but the cable box is OFF. NOTE: this time DO NOT HOLD THE CC button down, just press and hold down the CBL button. Firmly hold the CBL button down while pointing the remote at the cable box ( not the TV). When the cable box turns on, immediately remove your finger from the button. Now turn the CABLE box off and then back on by pressing the CBL button once ( Not the TV power button ). Next test channel up and down and the channel numbers. If the channels change correctly, make sure volume and TV power on and off operate, if so, you are done. If it is not working properly start again at step #5.

IMPORTANT TROUBLESHOOTING INFORMATION

If you think you missed the TV code or are testing remote on different brand TV's, or are having difficulty operating TV; first, reset the remote by pressing and holding the Setup button for 3 seconds and then while still pressing the Setup button down press and hold down the CC button at the same time until the LED light blinks quickly 3 times, instantly release both buttons. You have now reset the code list back to the beginning. Go back to step #1 and repeat all steps #1 through #5 again.

Note: Many cable boxes do not have a separate power button and are always on. If your cable box does have a separate power button, once you have set-up the cable box to work with the Clean Remote it can be powered on or off by pressing the CBL button.

TV ONLY INSTRUCTIONS, START HERE: If your TV is connected to an individual cable box in each guest room scroll up to step 1. Note: If you've already set up the remote to work both a TV and a Cable Box and now wish to operate TV only. Hold down the CBL button and SETUP button together until the remote blinks 3 times quickly instantly release both buttons. This will reset the remote completely.

Turn on the TV and then stand back about 5 feet from TV and Point the remote at the CENTER of the front panel of the TV. It will not be necessary to point the remote at that exact area once the remote is set-up.

Press and firmly Hold down the Setup button, do not release. The LED will blink once and then after 7 seconds it will initiate code search. The LED will continue to blink every 2 seconds. Once your TV shuts off immediately remove your finger from the Setup button; the code automatically locks in.

Test the remote. If everything works, you are done. If the main functions are not working properly, you may not have an exact code match. Start again at step #1. The code search will continue where it left off.

Important Note: If you think you missed the code or are testing remote on different brand TV's: Reset the remote back to the beginning of the code search; first press and hold the Setup button for 3 seconds and then while still pressing the Setup button down, press and hold the CC button down at the same time until the red LED light blinks quickly 3 times. You have now reset the code list back to the beginning

View PDF Version (Printable)

INSTRUCCIONES CLEAN REMOTE CR1, CR2BB

  • Solamente presione un botn (tecla) para configurar el control remoto (no se necesitan cdigos)
  • Solamente para televisores (no funciona con sistemas combinados, como TV/DVD, TV/VCR o TV/DVD/VCR)
  • Compatible con ms de 250 diferentes marcas comerciales de televisor
  • No tiene botn (tecla) de men, as que los pacientes o invitados no pueden cambiar la configuracin
  • El compartimento de las pilas (bateras) est escondido y atado por una bisagra para prevenir que le saquen las pilas (bateras)
  • Requiere 2 pilas (bateras) AAA
  • No funciona con los sistemas de pelcula de Lodgenet o On Command

Instrucciones para instalar las pilas (bateras)

  1. Para abrir el compartimiento de pilas (batera): Con el teclado frente a usted, presione la tapa negra hacia atrs (fig. A, paso1) y luego presione la tapa hacia arriba desde atrs. (foto A, paso 2).
  2. Cuando est instalando las pilas (bateras) AAA, asegrese que los smbolos + y - en el metal hagan contacto con los smbolos + y - de cada pila (batera).(foto B)
  3. Para cierre la tapa negra: Con el teclado as atrs, cierre suavemente, presionando hacia abajo (foto C, paso 1) a la vez que presionas la tapa hacia el frente (teclado) hasta que se alinee con el frente del control remoto (foto C, paso 2)
  4. Presione el botn (tecla) "POWER" para probar el control remoto, la luz se ilumina indicando que las pilas (bateras) estn bien. Si la luz no se ilumina es que las pilas (bateras) estn daadas o mal colocadas.

Solamente se requiere un paso para configurar el control remoto No hay necesidad de cdigos

Para todos los televisores

a. Prenda el televisor y de una distancia de 5 pies dirija el control remoto hacia el CENTRO de la pantalla. Este paso es solamente para la configuracin inicial del control remoto. Despus de este paso el control remoto funciona a distancias normales.

b. Presione y aguante el botn (tecla) de "SET-UP", un luz se iluminar, una vez y despus de 7 segundos adicionales el control remoto comenzar auto-configuracin. La luz iluminar cada 2 segundos durante este proceso. Tan pronto se apague su televisor, suelta el botn (tecla) y se completa el proceso.

c. Pruebe el control remoto. Si todo funciona comience a usar el telecontrol normalmente. Si las funciones principales no trabajan apropiadamente es que usted no ha encontrado la configuracin preferida. Recomenzar el proceso en paso b. para seguir auto-configuracin.

Importante: Si usted piensa que se paso de la configuracin correcta o desea reconfigurar el control remoto para otra marca de televisor tiene que restablecer la unidad. Primero presione y aguante el botn (tecla) de "SET-UP" por 3 segundos. Sin presionando el botn (teca) "SET-UP", presiona el botn (tecla) "CC" hasta que la luz se ilumina 3 veces. El control remoto esta restablecido, comenzar del paso b.

Copyright 2010, Starlight Electronics LLC, command In Hand Inc.

View PDF Version (Printable)

INSTRUCTIONS POUR LA TÉLÉCOMMANDE CR1, CR2BB CLEAN REMOTE MD

Compatible avec plus de 250 marques de téléviseurs d'usage
CLEAN REMOTEMD fonctionne seulement avec les téléviseurs (il ne convient pas aux téléviseurs avec lecteur de DVD ou de vidéocassettes, ni à des unités combinées.) Il est muni d'un compartiment à piles discret et d'un couvercle fixé pour empêcher le retrait des piles.
Utiliser deux piles AAA.

Installation de piles

  1. Ouvrez le couvercle. Tenez la télécommande, le clavier face à vous. Ouvrez le couvercle foncé en poussant dessus (photo A, étape 1), puis soulevez-le (photo A, étape 2).
  2. Insérez deux piles AAA en vous servant des symboles + et - sur la charnière de métal. Ceux-ci doivent entrer en contact avec les extrémités + et - de chacune des piles (photo B).
  3. Pour fermer le couvercle : tenez la télécommande, l'arrière face à vous. Abaissez doucement le couvercle en appuyant dessus (photo C, étape 1) et en le faisant glisser vers l'avant de la télécommande (côté clavier) jusqu'à ce qu'il soit bien aligné. (photo C, étape 2).
  4. Faites l'essai de la télécommande en appuyant sur la touche de marche/arrêt. Le voyant LED s'allumera si les piles ont été bien installées. Si le voyant ne s'allume pas, c'est que les piles ont été mal installées ou qu'elles sont épuisées.
  5. French

    Instructions pour des télévisions seulement

    1. Allumez le téléviseur, puis placez-vous à un peu moins de deux mètres de l'appareil. Pointez la télécommande sur le CENTRE du panneau avant du téléviseur. Il ne sera pas nécessaire de pointer la télécommande à ce même endroit une fois l'installation terminée.
    2. Appuyez sur le bouton Setup et maintenez-le enfoncé. Le voyant clignotera une fois. Après 7 secondes, la recherche du code commencera. Le voyant LED continuera de clignoter toutes les deux secondes. Lorsque le téléviseur s'éteint, relâchez immédiatement le bouton Setup. Le code est mis en mémoire automatiquement.
    3.  Faites l'essai de la télécommande. Si les commandes de base fonctionnent, vous avez terminé. Tous les boutons ne servent pas, car il s'agit d'une télécommande universelle. Si les principales commandes ne répondent pas adéquatement, il se peut que le code saisi ne soit pas exact. Recommencez la procédure à partir de l'étape 1. La recherche de code reprendra où elle a été abandonnée.

    Remarque importante : Si vous pensez avoir manqué le code ou si vous installez la télécommande pour plusieurs marques de téléviseur – Réinitialisez la télécommande avant de reprendre la recherche du code. D'abord, appuyez sur le bouton Setup et tenez-le enfoncé pendant 3 secondes. Tout en maintenant le bouton Setup enfoncé, appuyez sur le bouton CC et tenez-le enfoncé jusqu'à ce que le voyant LED rouge clignote rapidement trois fois. Vous avez réinitialisé la liste des codes. Recommencez la procédure à partir de l'étape 1.

View PDF Version (Printable)

INSTRUCTIONS FOR CR1R CLEAN REMOTE® (with at top)

(Remote for TV with CABLE BOX)

For TV or TV and separate Cable box only (will not work TV/DVD, TV/VCR or TV/DVD/VCR combination units) Works over 250 brands of commercial and retail TV's Simple One touch set-up (no codes needed) No Menu Button - So Patients and Guests cannot change settings Hidden Battery compartment and attached door to help prevent batteries from being taken Uses 2 AAA batteries Will not operate with LodgeNet® or On Command® movie systems

Battery Installation:

  1. Open cover: With keypad facing you, first slide dark lens cover away from you (photo A, step 1) and then lift lid upward from the back (photo A, step 2)
  2. When placing AAA batteries in the compartment note the + and - symbols on the metal hinge should make contact with the corresponding + and - end of each battery (photo B).
  3. Closing cover: With keypad facing away from you gently close cover by pressing downward (photo C, step 1) and sliding it toward the front (keypad) until it is aligned. (photo C, step 2)
  4. Test remote by pressing the power button; the LED should light indicating that the batteries are in correctly. If the LED doesn't light, then the batteries are either in wrong or the batteries are bad.
Battery Installation

NO CODE ENTRY/ONE STEP PROGRAMMING
If you have an Individual cable box In each room, Click Here.

  1. Turn on the TV and then stand back about 5 feet from TV and Point the remote at the CENTER of the front panel of the TV. It will not be necessary to point the remote at that exact area once the remote is set-up.
  2. Press and firmly Hold down the Setup button, do not release. The LED will blink once and then after 7 seconds it will initiate code search. The LED will continue to blink every 2 seconds. Once your TV shuts off immediately remove your finger from the Setup button; the code automatically locks in.
  3. Test the remote. If everything works, you are done. If the main functions are not working properly, you may not have an exact code match. Start again at step #1. The code search will continue where it left off.

Important Note: If you think you missed the code or are testing remote on different brand TV's: Reset the remote back to the beginning of the code search; first press and hold the Setup button for 3 seconds and then while still pressing the Setup button down, press and hold the CC button down at the same time until the red LED light blinks quickly 3 times, then release both buttons. You have now reset the code list back to the beginning. Go back to step 1.

FOR TV WITH AN INDIVIDUAL CABLE BOX IN EACH GUEST ROOM, START HERE: If you do not have an individual cable box in each guest room, click here.

  1. First step is to program the TV. The second step will then be to program the cable box.
  2. It is important that after you set up the TV you don't change the channels until after you complete the next step of setting up cable box.
  3. Turn on the TV and the Cable Box should also be on. Then stand back about 5 feet from the TV. Point the remote at the CENTER of the front panel of the TV. It will not be necessary to point the remote at that exact area once the remote is set-up.
  4. Press and firmly Hold down the Setup button, do not release. The LED will blink once and then after 7 seconds it will initiate code search. The LED will continue to blink every 2 seconds. Once your TV shuts off, immediately remove your finger from the Setup button; the code automatically locks in.
  5. Now test the remote by pressing the TV Power button testing On/Off and then the VOLUME + /- DO NOT PRESS CHANNEL +/- buttons as you may change input on TV. If power and volume buttons work correctly on the remote then proceed to step #6. If you accidentally changed the input on the TV, manually change it back from the TV's control panel and then try power and volume buttons ONLY. If the power and volume keys are not working properly, you may not have an exact code match. Start again at step #3, the code search will continue where it left off. Once you have the correct code, go to step #6 to program the cable box.
  6. To Program the Cable Box make sure the cable box and TV are on. Next, Hold Down the * button and CC button at the same time and wait until the LED light blinks quickly 3 times. Then immediately release both buttons. Now point the remote toward the cable box and TV and try the channel up and down buttons as well as the channel numbers. If the channels change correctly, make sure volume and TV power on and off work and if they do ,you are done.
  7. If the channels are not changing properly make sure the TV is on and this time turn the cable box OFF. NOTE: this time DO NOT HOLD THE CC button down, just press and firmly hold down the * button while pointing the remote at the cable box ( not the TV). The LED will blink once and then after 10 seconds it will initiate code search. The LED will continue to blink every 2 seconds. When the cable box turns ON, immediately remove your finger from the button and the code automatically locks in. Now turn the CABLE box off and then back on by pressing the CBL button once (Not the TV power button or * button). Next test channel up and down and the channel numbers. If the channels change correctly, make sure volume and TV power on and off operate, if so, you are done. If it is not working properly start again at step #6.

IMPORTANT TROUBLESHOOTING INFORMATION

A. If you think you missed the TV code or are testing remote on different brand TV's, or are having difficulty operating TV; first, reset the remote by pressing and holding the Setup button for 3 seconds and then while still pressing the Setup button down press and hold down the CC button at the same time until the LED light blinks quickly 3 times, instantly release both buttons. You have now reset the code list back to the beginning. Go back to step #1 and repeat all steps #1 through #7 again.

B. Reset remote to work TV only without a cable box. If you've already set up the remote to work both a TV and a Cable Box and now wish to operate TV only without a cable box. Hold down the * button and SETUP button together until the remote blinks 3 times quickly and immediately release both buttons. Then turn over the page and start at step 1 for TV only.

Note: Many cable boxes do not have a separate power button and are always on. If your cable box does have a separate power button, once you have set-up the cable box to work with the Clean Remote it can be powered on or off by pressing the CBL button.

View PDF Version (Printable)

INSTRUCTIONS FOR CR3BCB

For TV or TV and separate Cable box only (will not work TV/DVD, TV/VCR or TV/DVD/VCR combination units)
Works over 250 brands of commercial and retail TV's
Simple One touch set-up (no codes needed)
No Menu Button - So Patients and Guests cannot change settings
Hidden Battery compartment and attached door to help prevent batteries from being taken
Uses 2 AAA batteries
Will not operate with LodgeNet® or On Command® movie systems

Battery Installation:

1. Open cover: With keypad facing you, first slide dark lens cover away from you (photo A, step 1) and then lift lid upward from the back (photo A, step 2)
2. When placing AAA batteries in the compartment note the + and - symbols on the metal hinge should make contact with the corresponding + and - end of each battery (photo B).
3. Closing cover: With keypad facing away from you gently close cover by pressing downward (photo C, step 1) and sliding it toward the front (keypad) until it is aligned. (photo C, step 2)
4. Test remote by pressing the power button; the LED should light indicating that the batteries are in correctly. If the LED doesn't light, then the batteries are either in wrong or the batteries are bad.
1. Turn on the TV and then stand back about 5 feet from TV and Point the remote at the CENTER of the front panel of the TV. It will not be necessary to point the remote at that exact area once the remote is set-up.

2. Press and firmly Hold down the Setup button, do not release. The LED will blink once and then after 7 seconds it will initiate code search. The LED will continue to blink every 2 seconds. Once your TV shuts off immediately remove your finger from the Setup button; the code automatically locks in.

3. Test the remote. If everything works, you are done. If the main functions are not working properly, you may not have an exact code match. Start again at step #1. The code search will continue where it left off.

Important Note: If you think you missed the code or are testing remote on different brand TV's: Reset the remote back to the beginning of the code search; first press and hold the Setup button for 3 seconds and then while still pressing the Setup button down, press and hold the CC button down at the same time until the red LED light blinks quickly 3 times, then release both buttons. You have now reset the code list back to the beginning. Go back to step 1.


INSTRUCTIONS FOR NEW CLEAN REMOTE CR3BCB THAT HAS BUTTON AT THE BOTTOM OF THE REMOTE


If you do not have an individual cable box in each guest room, then turn sheet over to page 1

IF YOU HAVE A TV AND AN INDIVIDUAL CABLE BOX IN EACH GUEST ROOM, START HERE :

1.First step is to program the TV. The second step will then be to program the cable box.

2.It is important that after you set up the TV you don't change the channels until after you complete the next step of setting up cable box.

3.Turn on the TV and the Cable Box should also be on. Then stand back about 5 feet from the TV. Point the remote at the CENTER of the front panel of the TV. It will not be necessary to point the remote at that exact area once the remote is set-up.

4.Press and firmly Hold down the Setup button, do not release. The LED will blink once and then after 7 seconds it will initiate code search. The LED will continue to blink every 2 seconds. Once your TV shuts off, immediately remove your finger from the Setup button; the code automatically locks in.

5. Now test the remote by pressing the TV Power button testing On/Off and then the VOLUME + /- , DO NOT PRESS CHANNEL +/- buttons as you may change input on TV. If power and volume buttons work correctly on the remote then proceed to step #6. If you accidentally changed the input on the TV, manually change it back from the TV's control panel and then try power and volume buttons ONLY. If the power and volume keys are not working properly, you may not have an exact code match. Start again at step #3, the code search will continue where it left off. Once you have the correct code, go to step #6 to program the cable box.

6.To Program the Cable Box make sure the cable box and TV are on. Next, Hold Down the button and CC button at the same time and wait until the LED light blinks quickly 3 times. Then immediately release both buttons. Now point the remote toward the cable box and TV and try the channel up and down buttons as well as the the channel numbers. If the channels change correctly, make sure volume and TV power on and off work and if they do, you are done.

7.If the channels are not changing properly make sure the TV is on and this time turn the cable box OFF. (If setting up a box that does not have a separate power button and is always on, see notes at the bottom of this page.) NOTE: this time DO NOT HOLD THE CC button down, just press and firmly hold down the button while pointing the remote at the cable box ( not the TV). The LED will blink once and then after 10 seconds it will initiate code search. The LED will continue to blink every 2 seconds. When the cable box turns ON, immediately remove your finger from the button and the code automatically locks in. Now turn the CABLE box off and then back on by pressing the CBL button once (Not the TV power button or button). Next test channel up and down and the channel numbers. If the channels change correctly, make sure volume and TV power on and off operate, if so, you are done. If it is not working properly start again at step #6.

IMPORTANT TROUBLESHOOTING INFORMATION


A. If you think you missed the TV code or are testing remote on different brand TV's, or are having difficulty operating TV; first, reset the remote by pressing and holding the Setup button for 2 seconds and then while still pressing the Setup button down press and hold down the CC button at the same time until the LED light blinks quickly 3 times, immediately release both buttons. You have now reset the code list back to the beginning. Go back to step #1 and repeat all steps #1 through #7 again.

B. Reset remote to work TV only without a cable box. If you've already set up the remote to work both a TV and a Cable Box and now wish to operate TV only without a cable box. Hold down the button and SETUP button together until the remote blinks 3 times quickly and immediately release both buttons. Then turn over the page and start at step 1 for TV only.

Notes:


A) If setting up a cable box that does not have a separate power button and is always on. Follow the instructions on step 7, but release immediately if you see any change on the TV's picture or the lights on the box.

B) If your cable box does have a separate power button, once you have set-up the cable box to work with the Clean Remote it can be powered on or off by pressing the CBL button.

View PDF Version (Printable)